Skip to content
Preview. Prices and texts are drafts, orders are not fulfilled.

Features

We unlocked what the makers kept locked

Seven devices from our own home. Each one now does more than it did out of the box, and none of them asks its maker's cloud for permission any more. For each we also say what does not work yet.

58 °C2,2 kWh1:12Hugo

LG washer-dryer

The LG washer, fully unlocked

As sold, this machine can only be controlled through LG's servers, and even then only as far as LG allows. We switched it over to a small open-source program in our own home. It turned out the machine can do far more than its panel and LG's app let on.

  • Real remote control: start a wash from your phone or an automation without pressing a single button on the machine
  • Rinse hold and medic rinse, neither of which is on our panel
  • Temperatures between the panel's steps: a 50 °C wash, and the water really reaches 50 °C (measured)
  • Spin settings above the panel's maximum
  • Readings LG's app never shows: water temperature in the tub, drying air temperature, a warning when the detergent runs out
  • All of it with no LG account and no LG servers

Honest about the limits: the pause command does not work yet. The machine's own safety functions, such as the door interlock, stay untouched. The machine itself is not modified, and the change is reversible.

Service and price Read the story

Hugo

Robot vacuum + Valetudo

A robot that finally finishes the job

Our own Xiaomi X10+ worked through its maker's cloud and did only what the app allowed. Now it runs Valetudo, open-source software, and we can reach the parameters its maker never shows the owner.

  • The robot finishes the cleans it used to hang on
  • Better navigation, because the parameters can be tuned to the apartment
  • A stronger mop wash at the dock
  • Settings stay as you chose them and do not drift
  • The map, rooms and schedule stay in the robot and on your network, with no account

What we saw in factory mode: the robot was in constant contact with its maker's cloud and sent it its map. What happens to it after that is not visible from outside, so we claim nothing about it. Many models need opening and a small adapter, so we do this job at the workshop.

Service and price Read the story

HugoWi-Fi: 0

Sonoff DW2 + Hugo Door

Sensors with the Bluetooth their maker kept quiet about

As sold, the DW2 joins Wi-Fi every time and reports through the eWeLink cloud. That is slow and it drains the battery. With our Hugo Door firmware the sensor announces an opened door in a short, encrypted Bluetooth message, straight to your Home Assistant.

  • The Bluetooth its maker never mentions is now the main link
  • Far better battery life: the sensor sleeps and wakes only when the door moves
  • Reacts instantly: no waiting for the sensor to join Wi-Fi and reach a cloud
  • Messages are encrypted with a key that belongs to you
  • Home Assistant finds the sensor by itself. No Wi-Fi password in the sensor and no account.

The sensor needs a Bluetooth receiver nearby, such as our Basic R4 relay. A way back to the factory firmware exists.

DW2 in the shop Read the story

Hugo21,4 °C

Sonoff Basic R4 + ESPHome

A relay that is also a Bluetooth antenna

Inside a Basic R4 sits a chip with both Wi-Fi and Bluetooth. As sold, the relay just switches a light through its maker's app. With ESPHome it does two jobs at once: it switches the light locally and listens for Bluetooth sensors, passing their messages on to Home Assistant.

  • The light or appliance switches locally, even with no internet
  • Picks up Bluetooth door, temperature and motion sensors in the same room
  • Each further relay widens the coverage, with no separate Bluetooth receiver to buy
  • Sensors can be small and battery powered, because they do not have to keep Wi-Fi alive

In our home: three Basic R4 relays in our apartment run ESPHome with the Bluetooth receiver switched on. Leave the mains wiring to a certified electrician.

Basic R4 in the shop Read the story

Hugo

Sonoff ZBBridge Pro

A Sonoff bridge that is no longer Sonoff-only

As sold, the ZBBridge Pro works through the eWeLink app and cloud. We reflashed both of its chips, and now it is an open Zigbee coordinator connected straight to Home Assistant.

  • Zigbee devices from different makers on one network
  • Straight to Home Assistant: no app, no account, no cloud
  • Sits where the signal is best, not next to the server: it only needs Wi-Fi and a socket

After the switch, Zigbee devices have to be paired again. We keep a copy of the factory firmware.

ZBBridge Pro in the shop Service and price

21.446%HugoZigbee

Xiaomi LYWSD03MMC

A Xiaomi thermometer that finally works

This sensor costs a few euros and measures well, but as sold it needs Xiaomi's app and an account. We put open Zigbee firmware on it. Same device, same screen, but now it belongs to your network.

  • Zigbee instead of Bluetooth: reports straight to Home Assistant
  • No more maker's app and no account
  • Longer battery life

Reflashing happens over the air; the sensor is not opened.

The sensor in the shop Service and price

DNS · DNS · DNSHugo

Samsung smart TV

Even the TV is local now

When we started watching who our devices call on our own network, the TV was one of the loudest. Now it too is part of the local home: it is controlled from Home Assistant, not through its maker's cloud.

  • Control from Home Assistant and automations, locally
  • On our own network we see every address a device tries to reach
  • The same goes for the whole home: if a device calls out, we know

What we saw: the DNS requests on our own network. What exactly the TV sends is not visible from outside, so we claim nothing about the content.

Ask about your TV

Your device

Can this be done with mine?

Tell us the maker and model. If the device is on our list, you get the price straight away. If not, we offer a two-hour feasibility check at a fixed price, and publish the result for everyone.

Prices and ordering Get in touch